ISO 13954/13955 — read the full explanation
Peel & adhesionPE electrofusion assemblies — peel decohesion and crushing decohesion tests.
Peel & adhesion
Peel Adhesion Tester
One bonded layer is pulled away from the other at a fixed angle and rate, so the force it takes to separate them is measured along the whole bond, not just at the point it lets go.
Runs onSeries 7200
AS/NZS 2111.16
Peel & adhesionTextile floor coverings — bond strength determination (delamination of backing).
ASTM C633 — read the full explanation
Peel & adhesionAdhesion or cohesion strength of thermal spray coatings (tension pull-off).
ASTM C794 — read the full explanation
Peel & adhesionAdhesion-in-peel of elastomeric joint sealants (construction sealants).
ASTM D1335 — read the full explanation
Peel & adhesionTuft bind of pile yarn floor coverings (force to pull a tuft from carpet backing).
ASTM D1781 — read the full explanation
Peel & adhesionClimbing drum peel for adhesives — sandwich facings and laminated assemblies (aerospace).
ASTM D1871
Peel & adhesionAdhesion of single-strand bead wire to rubber (tyre bead construction).
ASTM D1871 / D885
Peel & adhesionBead wire and tyre cord adhesion/tensile for tyre plants.
ASTM D1876 — read the full explanation
Peel & adhesionT-peel resistance of adhesives (flexible-to-flexible adherends).
ASTM D3167 — read the full explanation
Peel & adhesionFloating roller peel resistance of adhesives (metal-to-metal bonds).
ASTM D3330 — read the full explanation
Peel & adhesionPeel adhesion of pressure-sensitive tape (180°, 90° and adhesion-to-liner methods).
ASTM D413 — read the full explanation
Peel & adhesionAdhesion of rubber to fabric or flexible substrate (ply separation).
ASTM D429 — read the full explanation
Peel & adhesionAdhesion of rubber to rigid substrates (Methods A, B, C — tension and 90° peel).
ASTM D4541 — read the full explanation
Peel & adhesionPull-off strength of coatings (adhesion testers; also performed on UTM with suitable fixtures).
ASTM D5169/D5170 — read the full explanation
Peel & adhesionHook-and-loop touch fasteners — shear strength and 180° peel strength.
ASTM D6862 — read the full explanation
Peel & adhesion90° peel resistance of adhesives.
ASTM D903 — read the full explanation
Peel & adhesionPeel or stripping strength of adhesive bonds (180° peel).
ASTM F2256 — read the full explanation
Peel & adhesionStrength of tissue adhesives in T-peel by tension loading (medical).
ASTM F88 — read the full explanation
Peel & adhesionSterile barrier packaging — seal peel strength validation.
ASTM F88 / F88M
Peel & adhesionSeal strength of flexible barrier materials — heat-sealed pouches and medical packaging.
EN 12004
Peel & adhesionTile adhesive tensile adhesion strength classification.
EN 12311
Peel & adhesionBituminous and polymeric waterproofing membranes — tensile, peel and shear of joints.
EN 12316
Peel & adhesionBituminous and polymeric waterproofing membranes — tensile, peel and shear of joints.
EN 12317
Peel & adhesionBituminous and polymeric waterproofing membranes — tensile, peel and shear of joints.
EN 1348 — read the full explanation
Peel & adhesionAdhesives for tiles — tensile adhesion (pull-off) strength of cementitious adhesives.
EN ISO 1402-adjacent
Peel & adhesionRubber hose — tensile of tube/cover, adhesion between layers (burst tests via hydraulic rigs).
IEC 61215-adjacent
Peel & adhesionPV ribbon solder-joint peel and backsheet adhesion testing.
IS 1891-1
Peel & adhesionRubber conveyor belts — tensile and adhesion requirements. Equivalent to: ISO 283 / 252
IS 2770
Peel & adhesionBond strength between reinforcing steel and concrete — pull-out test.
IS 2770-1
Peel & adhesionRebar-to-concrete bond strength by pull-out test.
IS 443
Peel & adhesionRubber hose — tensile of tube/cover, adhesion between layers (burst tests via hydraulic rigs).
ISO 8510-2 — read the full explanation
Peel & adhesion180 degree peel test for a flexible adherend bonded to a rigid one.
ASTM D6252/D6252M — read the full explanation
Peel & adhesion90 degree peel adhesion of pressure-sensitive label stocks.
ISO 11339 — read the full explanation
Peel & adhesionT-peel test for flexible-to-flexible bonded assemblies.
ISO 11607-1 — read the full explanation
Peel & adhesionPackaging for terminally sterilized medical devices — seal strength verification (references F88-type peel).
ISO 11644 — read the full explanation
Peel & adhesionLeather — adhesion of surface finish coating.
ISO 13954
Peel & adhesionTensile and peel decohesion testing of PE pipe welded joints.
ISO 13954 / 13955
Peel & adhesionPE electrofusion assemblies — peel decohesion and crushing decohesion tests.
ISO 14270 — read the full explanation
Peel & adhesionMechanized peel testing of resistance spot, seam and embossed projection welds.
ISO 17708 — read the full explanation
Peel & adhesionWhole-shoe sole adhesion (peel) testing.
ISO 1827 — read the full explanation
Peel & adhesionShear modulus and adhesion of rubber to rigid plates — quadruple-shear method (anti-vibration mounts).
ISO 20344
Peel & adhesionSafety footwear — toe cap compression, penetration resistance, sole bond.
ISO 20588-adjacent
Peel & adhesionAdhesion of bead wire to rubber; tensile of tyre cords and dipped fabrics.
ISO 2411 — read the full explanation
Peel & adhesionCoated fabrics — coating adhesion (peel of coating from substrate).
ISO 252 — read the full explanation
Peel & adhesionConveyor belts — adhesion between constitutive elements (ply-to-ply and cover-to-ply, tested as peel on UTM).
ISO 36 — read the full explanation
Peel & adhesionAdhesion of rubber to textile fabrics.
ISO 7622
Peel & adhesionSteel cord belts — cord tensile, cord-to-rubber adhesion and splice strength.
ISO 7623 — read the full explanation
Peel & adhesionSteel cord conveyor belts — cord-to-coating adhesion test (initial and after thermal treatment).
ISO 813 — read the full explanation
Peel & adhesionAdhesion of rubber to rigid substrate — 90° peel and tension methods.
ISO 813 / 814
Peel & adhesionRubber-to-metal bond strength — mounts, bushings, rollers, linings.
ISO 814
Peel & adhesionAdhesion of rubber to rigid substrate — 90° peel and tension methods.
ISO 8510-1 / -2
Peel & adhesion90° and 180° peel test for flexible-bonded-to-rigid assemblies.
SAE J20-adjacent
Peel & adhesionHose tube/cover tensile, elongation and layer adhesion.
Showing 1–8 of 53 standards
Next
Tell us the specimen, not just the standard.
Thickness, width and expected break force decide the grip as much as the method does. Send us those and we will specify the frame, the load cell and the fixture around them.